- 4 black steel 1 ⅝” 7 ½’ finished height fence support posts
- 4 caps for posts (pre-installed on posts)
- 4 no-dig ground sleeves for posts
- 4 locking set screws installed in sleeves (makes posts removable or permanent. Patent pending)
- 8 black steel 1 ⅜” 89” framing posts
- 1 7 ½’ x 100’ roll of Critterfence 650 black 1" opening size Bird & Deer Net
- 1 10" 120-lb breaking strength black fence ties (100pk)
- 1 12" kinked galvanized ground stakes (30pk)
- 4 1 ⅜” to 1 ⅜” black end clamp hardware
- 2 1 ⅝” to 1 ⅜” black end clamp hardware
- 4 1 ⅝” to 1 ⅜” black center clamp hardware
- 25 black self-tapping screws
- 1 set of fence instructions
Installed rear extension kit dimensions: 7 ½-foot wide by 15-foot long, with 7 ½-foot tall outside and 7-foot inside overhead clearance.
These add-on kits will only work in conjunction with another kit (Fence Kit With Top 1 in this case). Some of the hardware in your original kit will be reused or replaced with new hardware from this kit.
Bottom wire: These fence kits with top don't include chew protection, which may not be necessary or apply to your project. If you need to add steel wire to the bottom of this fencing, please visit our metal fence rolls page and select the fencing type. If you do decide to add it, here's what's suggested:
- 2’ Critterfence Steel Web 1" opening size, used to exclude most small animals and rabbits
- 3’ Critterfence Steel Web 1" opening size, same as above, but with added height for groundhogs/woodchucks, dog containment, or coyote exclusion
- 4’ Critterfence Steel Web 1" opening size, same as above, but added additional width. This is typically used by customers who want to increase the amount of overlap on the ground from the standard 6", or who wish to bury part of the fencing as a dig barrier
- 2’, 3’, and 4’ tall 1/2" Opening Steel Grid. Used for the same applications above, only this mesh has a smaller opening size. This metal bottom wire fencing is used to exclude even the smallest animals, including moles, voles, and snakes. It's roughly twice as heavy and strong as our Steel Web fencing.
You can also choose a different fence kit that uses all metal fencing, Fence Kit With Top 4.
Notes:
- Posts are round galvanized inside and out, then black powder-coated
- No-dig sleeves are heavily galvanized inside and out for extreme long-life
- Ground sleeves go into the ground 30”
- The finished height of the fence posts is the height above ground (for example, an item with 8’ finished height is 8’ above the ground level once the sleeve is in the earth and the post has been installed into the sleeve)
- All posts with ground sleeves can be installed permanently or made removable
- No-dig ground sleeves get driven into the ground with a sledgehammer, posts then slide inside the sleeve and lock in with a locking set screw (patent pending)
- To remove posts for seasonal protection or to move your fence: 1) cut fence ties holding fence to posts; 2) roll up fencing; 3) slide post up out of sleeve
- To make posts permanent, tighten the locking set screw in each sleeve to prevent the post from spinning or coming up out of the post
- For rocky or heavily compacted ground, we suggest using a San Angelo digging bar to pilot the hole for sleeves (instructions with kit)
- You can also use a powered drill or hammer drill with our sleeve auger bit
These fence kits are designed to be installed on level and flat areas. If you're installing this over an area that has a slope or is pitched in one direction, some cutting or modifying of the fence post height will be required. This may make the overall height of your fence shorter. For example, if you are installing in an area that slopes from higher to lower, to make the enclosure level, you would cut the front posts 1 inch, the middle posts ½ inch, and leave the rear posts.
These fence kits start with approximately 7 feet of overhead clearance. The side posts are 7 ½ feet out of the ground, but some space is needed for the framing and side bracing. Access gates are available separately; select 7-foot-tall gates or shorter for proper installed clearance.
